Heavy Duty Swivel

12 gauge steel with a double race 10 1/4 by 10 1/4 flat pitch

Mounting holes are on 8" centers

#118 $42.50 each

$16.00 each.

Part Number 120160 $ 21.95 each

Brown legs with plastic feet. 

Mounting plate measures 5 3/4" x 8 1/2", at mounting holes.

Steam Bent Oak Rocker Runners

Length measures strait across from tip to tip. Stronger than cut rockers   Sold in pairs only. unfinished red oak will require drilling sanding and finishing.

Note: Second Day and Next Day shipments of table slides will be billed actual shipping cost due to being oversize. The shopping cart will not figure the shipping price correctly, but we will adjust it on our end. We can provide a shipping quote by request before you order them.

          1 5/16" high by 34 1/4" long by 5/8" thick         
Limited Stock

1 5/16" high by 34 1/4" long by 1 1/8" thick      

1 5/16" high by 34 1/4" long by 1 7/8" thick      

Cut Oak Rocker Runners

1 3/4" high by 34 1/2" long by 1 1/16" thick       

1 3/4" high by 37" long by 1 9/16" thick             

Curved Rocking Chair Seat

  Oak face and back. It must be shaped and cut to fit your particular rocker. Send us a sketch of your formed shape before ordering to make sure it will fit. We can provide this one curvature only. Our supplier doesn't have any other shape molds.  24" to 25"long following the curve.  3/16" thick,   20" plus wide.    

Oak Hip Huggers

 6 1/2" high by 5 1/4" deep by 7/8" diameter. 11" long from tip to tip measuring along the curve. **Please note: All measurements are approximate. One end is sanded flat to fit the chair seat. The other end is carved out to fit the back spindle. Screw holes are pre-drilled. Unfinished, sanded, ready to install. Ends are pointed. One left hand and one right hand hip hugger required per chair. Sold in pairs only. 

Hip hugger Clips

Outside dimensions - 1" long by 11/16" wide by  1/2" high. Screw hole - 1/4" diameter.  Made to fit 7/8" hip huggers. Sold in sets of four. 

Morris Chair Brackets  

7 3/4" long by 15/16" wide.  Hooks will accommodate 3/8" to 1/2" diameter rods. The common angle of the brackets will adapt to the curve of most Morris chairs. Sold by the pair.

Morris Chair Rod

Overall - 29 3/4" long. 

  Rod - 28 1/4" long by 3/8" diameter. Beehive finials - 3/4" long by 7/8" diameter.

  Finials are attached with set screws which can be removed, allowing the rod to be cut to length if necessary.

Platform Rocker Springs

All springs are sold by the pair which will do one chair.

Heavy Duty - 7 gauge  Eight turns. S-5242  $15.10

Single Juvenile  Platform Rocker Springs. S-5243 $5.90

Oak High Chair Parts

20 1/2" wide   11 3/4" deep.     1 3/32" thick  with  Routed center.

16" wide by 8 1/2" deep at center.       7" deep at ends.

Bent Oak High Chair Tray Arms

Overall length - 18 1/2" long   23" long following the curve.   Flat area - Approximately 13"    7/8" Square. Sold by the pair with spacers.

High Chair Tray Hardware

  Arm piece - 6" L x 5/8" w x 7/8" deep.   Tray Piece - 3 5/16" L x 1" w x 15/16" deep.

Best for use with our W3-5226 tray or similar styles only. Comes as a set for attaching one high chair tray. The long piece attaches to the outside of the arm. The short piece attaches to the underside of the tray. The spring loaded clamp allow the position of the tray to be adjusted then locked into place. This style of hardware began to appear on high chairs in the 1940's.     

High Chair Safety Strap

13" long by 5/8" wide  Natural leather.  Includes screw snap for easy installation. Instructions included.  

10% Discount on Orders $50.00 or More.